How to remove and install a balljoint using the picklefork and puller methods on Lexus RX350?

It is recommended that the wheel lug nuts be loosened, the car raised and supported on jack stands before the wheel is removed. If intending to use a puller for the balljoint, then it is advisable to slacken the driveaxle/hub nut before lifting the car. First, make sure to provide a ball joint stud, then, to eliminate the cotter pin and then, unscrew the nut halfway but not more. Disengage the ball joint from the steering knuckle with the use of the picklefork-type ball joint separator after which remove the ball joint stud nut. After that, remove the bolt and nuts used to fix the ball joint to the control arm, then use the pry bar to disengage ball joint from the control arm. When fitting stick the new balljoint into position on the steering knuckle and thread on the nut but do not over tighten it at this stage. Fix the ball joint to the control arm, next put in the bolt and nuts then tighten the nuts to the recommended torque. The balljoint stud nut should then be tightened to the required torque and a new cotter pin be fitted with the hole in the cotter pin engaging the slots on the nut; if not align the nut by tightening it without loosening it. Bolt the wheel and the lug nuts back in place, raise the vehicle and then tighten the lug nuts to the required measure. Where the puller method is applied, if used to removed the wheel speed sensor, and then loosen and unbolt the control arm to ball-joint and further unfasten the outer part of the driveaxle from the steering knuckle and suspend with a wire. Again unbolt the cotter pin and the nut, after which, use a small puller and place it over the ball joint stud and pull it to detach it from the steering knuckle Thus; remove the nut and the ball joint. Replace the new ball joints into the steering knuckle, and make sure that it is tightened to the right torque, also use a new cotter pin so that it can align properly. Push the outer end of the driveaxle to the steering knuckle and screw in the nut tightly, but do not overtighten it at this stage. Fasten the balljoint to the lower arm and while fastening make sure that the fasteners attain the following torque. Replace wheel speed sensor and then the wheel then the lug nuts, drop the car and then again tighten the lug nuts to the recommended torque. Last of all, ensure that the driveaxle/hub nut is properly torqued to the correct specifications and then go ahead and staking the nut.

Genuine Lexus RX350 Ball Joint

Control Arm Joint

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Ball Joints found

View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Right
Part Number: 43330-09780
$72.93 MSRP: $98.63
You Save: $25.70 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Rh; Lower Ball Joint
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2022 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; GGL10L-CWTGKA, GGL15L-CWTGKA, GGL15L-CWZGKA, GGL20L-CWZGBA, GGL25L-CWZGBA, GYL10L-CWXGKA, GYL15L-CWXGKA, GYL20L-CWXGBA, GYL25L-CWXGBA
View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Left
Part Number: 43340-49035
$62.59 MSRP: $84.65
You Save: $22.06 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Lh; Lower Ball Joint
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2022 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; GGL10L-AWTGKA, GGL15L-AWTGKA, GGL25L-AWZGBA, GGL25L-BWZGBA, GYL10L-AWXGKA, GYL15L-AWXGKA, GYL25L-AWXGBA
View related parts
Lexus RX350 Front Lower Suspension Ball Joint Assembly, Right
Part Number: 43330-49165
$72.31 MSRP: $97.79
You Save: $25.48 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Rh; Lower Ball Joint
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2022 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; GGL10L-AWTGKA, GGL15L-AWTGKA, GGL25L-AWZGBA, GGL25L-BWZGBA, GYL10L-AWXGKA, GYL15L-AWXGKA, GYL25L-AWXGBA
View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Left
Part Number: 43340-09140
$72.31 MSRP: $97.79
You Save: $25.48 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Lh; Lower Ball Joint
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2022 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; 2GRFE, 2GRFKS, 2GRFXE, 2GRFXS; GGL10L-CWTGKA, GGL15L-CWTGKA, GGL15L-CWZGKA, GGL20L-CWZGBA, GGL25L-CWZGBA, GYL10L-CWXGKA, GYL15L-CWXGKA, GYL20L-CWXGBA, GYL25L-CWXGBA
View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Left
Part Number: 43340-09010
$68.01 MSRP: $91.97
You Save: $23.96 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Lh; Ball Joint, Lower Ball Joint
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lexus RX350 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; 2GRFE, 3MZFE; GSU30L-CWAGKA, GSU35L-CWAGKA, MCU33L-CWAGKA, MCU38L-CWAGKA
View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Right
Part Number: 43330-09560
$71.57 MSRP: $96.79
You Save: $25.22 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Rh; Ball Joint, Lower Ball Joint
- Position: Front Passenger Side
- Replaces: 43330-09160
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lexus RX350 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; 2GRFE; GSU30L-CWAGKA, 3MZFE; MCU33L-CWAGKA, GSU35L-CWAGKA, MCU38L-CWAGKA
View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Left
Part Number: 43340-29175
$70.61 MSRP: $93.96
You Save: $23.35 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Lh
- Position: Front Driver Side
- Replaced by: 43340-29215
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2008 Lexus RX350 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; 2GRFE, 3MZFE; GSU30L-AWAGKA, GSU35L-AWAGKA, MCU33L-AWAGKA, MCU38L-AWAGKA
View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Right
Part Number: 43330-29615
$69.48 MSRP: $93.96
You Save: $24.48 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Rh; Lower Ball Joint
- Position: Front Passenger Side
- Replaces: 43330-29405
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lexus RX350 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; 2GRFE, 2GRFE; GSU30L-AWAGKA, 3MZFE; GSU30L-AWAGKA, GSU35L-AWAGKA, MCU33L-AWAGKA, MCU38L-AWAGKA
View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Right
Part Number: 43330-29405
$70.61 MSRP: $93.96
You Save: $23.35 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Rh
- Position: Front Passenger Side
- Replaced by: 43330-29615
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2008 Lexus RX350 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; 2GRFE, 3MZFE; GSU30L-AWAGKA, GSU35L-AWAGKA, MCU33L-AWAGKA, MCU38L-AWAGKA
View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Left
Part Number: 43340-29215
$69.48 MSRP: $93.96
You Save: $24.48 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Lh; Lower Ball Joint
- Position: Front Driver Side
- Replaces: 43340-29175
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lexus RX350 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; 2GRFE, 2GRFE; GSU30L-AWAGKA, 3MZFE; GSU30L-AWAGKA, GSU35L-AWAGKA, MCU33L-AWAGKA, MCU38L-AWAGKA
View related parts
Lexus RX350 Front Lower Ball Joint Assembly, Right
Part Number: 43330-09160
$72.74 MSRP: $96.79
You Save: $24.05 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Joint Assy, Lower Ball, Front Rh
- Position: Front Passenger Side
- Replaced by: 43330-09560
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007 Lexus RX350 | STD | 6 Cyl 3.3L | 3MZFE; 3MZFE; MCU33L-CWAGKA, MCU38L-CWAGKA
View related parts
Lexus RX350 JOINT ASSY, LWR BALL
Part Number: 43330-49245
$86.09 MSRP: $116.42
You Save: $30.33 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lower Ball Joint
- Position: Lower
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2023-2025 Lexus RX350 | 4 Cyl 2.4L, 4 Cyl 2.5L | A25AFXS, T24AFTS; A25AFXS, T24AFTS; AALH15L-AWXGBA, AALH16L-AWXGBA, TALA10L-AWZGTA, TALH17L-AWTGTA
View related parts
Lexus RX350 JOINT ASSY SET, LWR
Part Number: 43330-09B60
$63.33 MSRP: $85.65
You Save: $22.32 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lower Ball Joint
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2023-2025 Lexus RX350 | 4 Cyl 2.4L, 4 Cyl 2.5L | A25AFXS, T24AFTS; A25AFXS, T24AFTS; AALH15L-CWXGBA, TALA10L-CWZGTA, TALA15L-CWZGTA, TALH17L-CWTGTA
View related parts
Lexus RX350 JOINT ASSY SET, LWR
Part Number: 43330-09C40
$81.54 MSRP: $110.27
You Save: $28.73 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lower Ball Joint
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2023-2024 Lexus RX350 | 4 Cyl 2.4L, 4 Cyl 2.5L | A25AFXS, T24AFTS; A25AFXS, T24AFTS; AALH15L-CWXGBA, TALA10L-CWZGTA, TALA15L-CWZGTA, TALH17L-CWTGTA

Lexus RX350 Ball Joint

Should you need to purchase new auto parts for your vehicle, we strongly suggest you consider the genuine Lexus RX350 Ball Joint available on LexusPartsNow.com. Our OEM Lexus RX350 Ball Joint come with the reassurance of the manufacturer's warranty, a hassle-free return policy, and speedy delivery service, all at affordable prices online. Feel free to shop with confidence!

Lexus RX350 Ball Joint Parts Questions & Experts Answers

Front Lower Ball Joint Assembly, Left
43340-49035
Q: How to remove and install a balljoint using the picklefork and puller methods on Lexus RX350?
A: It is recommended that the wheel lug nuts be loosened, the car raised and supported on jack stands before the wheel is removed. If intending to use a puller for the balljoint, then it is advisable to slacken the driveaxle/hub nut before lifting the car. First, make sure to provide a ball joint stud, then, to eliminate the cotter pin and then, unscrew the nut halfway but not more. Disengage the ball joint from the Steering Knuckle with the use of the picklefork-type ball joint separator after which remove the ball joint stud nut. After that, remove the bolt and nuts used to fix the ball joint to the Control Arm, then use the pry bar to disengage ball joint from the control arm. When fitting stick the new balljoint into position on the steering knuckle and thread on the nut but do not over tighten it at this stage. Fix the ball joint to the control arm, next put in the bolt and nuts then tighten the nuts to the recommended torque. The balljoint stud nut should then be tightened to the required torque and a new cotter pin be fitted with the hole in the cotter pin engaging the slots on the nut; if not align the nut by tightening it without loosening it. Bolt the wheel and the lug nuts back in place, raise the vehicle and then tighten the lug nuts to the required measure. Where the puller method is applied, if used to removed the wheel speed sensor, and then loosen and unbolt the control arm to ball-joint and further unfasten the outer part of the driveaxle from the steering knuckle and suspend with a wire. Again unbolt the cotter pin and the nut, after which, use a small puller and place it over the ball joint stud and pull it to detach it from the steering knuckle Thus; remove the nut and the ball joint. Replace the new ball joints into the steering knuckle, and make sure that it is tightened to the right torque, also use a new cotter pin so that it can align properly. Push the outer end of the driveaxle to the steering knuckle and screw in the nut tightly, but do not overtighten it at this stage. Fasten the balljoint to the lower arm and while fastening make sure that the fasteners attain the following torque. Replace wheel speed sensor and then the wheel then the lug nuts, drop the car and then again tighten the lug nuts to the recommended torque. Last of all, ensure that the driveaxle/hub nut is properly torqued to the correct specifications and then go ahead and staking the nut.

Related Lexus RX350 Parts

Browse by Year

2025 Ball Joint 2024 Ball Joint 2023 Ball Joint 2022 Ball Joint 2021 Ball Joint 2020 Ball Joint 2019 Ball Joint 2018 Ball Joint 2017 Ball Joint 2016 Ball Joint 2015 Ball Joint 2014 Ball Joint 2013 Ball Joint 2012 Ball Joint 2011 Ball Joint 2010 Ball Joint 2009 Ball Joint 2008 Ball Joint 2007 Ball Joint