How to remove and install Intake Manifold in Four cylinder engine on Lexus RX350?

To remove the intake manifold, first relieve the fuel system pressure and disconnect the cable from the negative battery terminal. Next, remove the air intake duct and resonator, followed by the cowl cover assembly. Then, take out the fuel rail and injectors as an assembly. For models from 1999 to 2007, remove the throttle linkage and throttle body from the intake manifold, label and detach the PCV and vacuum hoses connected to the intake manifold, and securely support the vehicle on jackstands. If working on a 4WD model, loosen the right side driveaxle/hub nut and the right front wheel lug nuts before raising the vehicle. Drain the transfer case lubricant, remove the right side driveaxle, and separate the transfer case mount from the transfer case, removing the transfer case mounting brace. For all models, work below the vehicle to remove the manifold lower mounting bolts, then from above, remove the intake manifold upper mounting nuts and bolts, and take out the manifold, gasket, and manifold insulator from the engine. For models from 2008 and later, remove the engine cover, disconnect the vacuum hoses and ventilation tubes from the intake manifold, and remove the throttle body with the electronic throttle actuator. Additionally, remove the windshield wiper motor, brake booster vacuum bracket, and outer cowl top assembly, then disconnect and remove the main harness connector to the intake manifold and tumble control valves. Apply battery voltage to the tumble control valve electrical connector to close the valve, preventing damage during removal. Remove the intake manifold support bracket and disconnect the vacuum switching valve assembly electrical connector, then unscrew the intake manifold mounting fasteners and remove the manifold. For installation, clean the mating surfaces of the intake manifold and cylinder head mounting surface, checking the gasket for leaks and the manifold for warpage. Press a new gasket into the grooves on the intake manifold, install the manifold and gasket over the studs on the cylinder head, and tighten the manifold-to-cylinder head nuts/bolts in three or four equal steps from the center outwards. Reinstall the remaining parts in reverse order, check the coolant level, refill the transfer case for 4WD models, and ensure the throttle linkage operates smoothly before starting the engine to check for coolant and vacuum leaks.

Genuine Lexus RX350 Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Intake Manifolds found

View related parts
Lexus RX350 Manifold, Intake
Part Number: 17111-0P030
$399.66 MSRP: $553.98
You Save: $154.32 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSU30L-CWAGKA, GSU35L-CWAGKA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-31061
$732.60 MSRP: $1015.49
You Save: $282.89 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Plenum
- Replaces: 17190-31060
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSU30L-AWAGKA, GSU35L-AWAGKA
View related parts
Lexus RX350 MANIFOLD ASSY, INTAK
Part Number: 17120-F0100
$330.23 MSRP: $457.74
You Save: $127.51 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Manufacturer Note: (L)
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2023-2025 Lexus RX350 | 4 Cyl 2.4L | T24AFTS; T24AFTS; TALA10L-CWZGTA, TALA15L-CWZGTA, TALH17L-CWTGTA
View related parts
Lexus RX350 Manifold, Intake
Part Number: 17111-31141
$399.77 MSRP: $554.13
You Save: $154.36 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2015 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE, 2GRFXE; 2GRFE, 2GRFXE; GGL10L-AWTGKA, GGL10L-CWTGKA, GGL15L-AWTGKA, GGL15L-CWTGKA, GSU30L-AWAGKA, GSU30L-CWAGKA, GSU35L-AWAGKA, GSU35L-CWAGKA, GYL10L-AWXGKA, GYL10L-CWXGKA, GYL15L-AWXGKA, GYL15L-CWXGKA
View related parts
Lexus RX350 MANIFOLD ASSY, INTAK
Part Number: 17120-25080
$472.75 MSRP: $655.30
You Save: $182.55 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Manufacturer Note: (J)
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2023-2025 Lexus RX350 | 4 Cyl 2.4L | T24AFTS; T24AFTS; TALA10L-AWZGTA, TALH17L-AWTGTA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-0P041
$732.60 MSRP: $1015.49
You Save: $282.89 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 17190-0P042
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GSU30L-CWAGKA, GSU35L-CWAGKA
View related parts
Lexus RX350 Manifold, Intake
Part Number: 17111-0P060
$289.12 MSRP: $400.75
You Save: $111.63 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Manufacturer Note: (L)
- Replaces: 17111-0P050
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2016-2022 Lexus RX350 | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GGL20L-CWZGBA, GGL25L-CWZGBA
View related parts
Lexus RX350 Manifold, Intake
Part Number: 17101-20070
$316.04 MSRP: $438.08
You Save: $122.04 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Replaces: 17101-0A050
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2007 Lexus RX350 | STD | 6 Cyl 3.3L | 3MZFE; 3MZFE; MCU33L-AWAGKA, MCU33L-CWAGKA, MCU38L-AWAGKA, MCU38L-CWAGKA
View related parts
Lexus RX350 Manifold Assembly INTAK
Part Number: 17120-F0020
$330.23 MSRP: $457.74
You Save: $127.51 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Replaces: 17120-25020
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2023-2025 Lexus RX350 | 4 Cyl 2.5L | A25AFXS; A25AFXS; AALH15L-AWXGBA, A25AFXS; AALH15L-CWXGBA, AALH16L-AWXGBA
View related parts
Lexus RX350 Manifold, Intake
Part Number: 17111-0P040
$411.90 MSRP: $570.94
You Save: $159.04 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2015 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GGL10L-CWTGKA, GGL15L-CWTGKA, GGL15L-CWZGKA
View related parts
Lexus RX350 Manifold, Intake
Part Number: 17111-31230
$413.93 MSRP: $573.76
You Save: $159.83 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Manufacturer Note: (J)
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2016-2022 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GGL20L-CWZGBA, GGL25L-AWZGBA, GGL25L-BWZGBA, GGL25L-CWZGBA
View related parts
Lexus RX350 Manifold Assembly, Intake
Part Number: 17120-31070
$414.10 MSRP: $573.99
You Save: $159.89 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Intake; Intake Manifold
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2016-2022 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFXS; 2GRFXS; GYL20L-CWXGBA, GYL25L-AWXGBA, GYL25L-CWXGBA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-0P070
$729.43 MSRP: $1011.09
You Save: $281.66 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: (L)
- Replaced by: 17190-0P071
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2013 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GGL10L-CWTGKA, GGL15L-CWTGKA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-0P071
$729.43 MSRP: $1011.09
You Save: $281.66 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Plenum
- Manufacturer Note: (L)
- Replaces: 17190-0P070
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2015 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GGL10L-CWTGKA, GGL15L-CWTGKA, GGL15L-CWZGKA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-31130
$729.43 MSRP: $1011.09
You Save: $281.66 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 17190-31250
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2014 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFXE; 2GRFXE; GYL10L-AWXGKA, GYL15L-AWXGKA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-31250
$729.43 MSRP: $1011.09
You Save: $281.66 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Plenum
- Manufacturer Note: (L)
- Replaces: 17190-31130
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2015 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFXE; 2GRFXE; GYL10L-AWXGKA, GYL10L-CWXGKA, GYL15L-AWXGKA, GYL15L-CWXGKA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-0P110
$739.07 MSRP: $1024.45
You Save: $285.38 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold, Intake Plenum, Plenum
- Replaces: 17190-31270
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2016-2022 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GGL20L-CWZGBA, 2GRFKS; GGL25L-AWZGBA, GGL25L-BWZGBA, GGL25L-CWZGBA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-31270
$739.07 MSRP: $1024.45
You Save: $285.38 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 17190-0P110
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2016-2022 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFKS; 2GRFKS; GGL25L-AWZGBA, GGL25L-BWZGBA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-31280
$739.07 MSRP: $1024.45
You Save: $285.38 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Plenum, Plenum
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2016-2022 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFXS; 2GRFXS; GYL20L-CWXGBA, GYL25L-AWXGBA, GYL25L-CWXGBA
View related parts
Lexus RX350 Tank Assy, Intake Air Surge
Part Number: 17190-31120
$841.39 MSRP: $1166.28
You Save: $324.89 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: (J)
- Replaced by: 17190-31121
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2010-2012 Lexus RX350 | STD | 6 Cyl 3.5L | 2GRFE; 2GRFE; GGL10L-AWTGKA, GGL10L-CWTGKA, GGL15L-AWTGKA, GGL15L-CWTGKA

| Page 1 of 2 |Next >

1-20 of 24 Results

Lexus RX350 Intake Manifold

Should you need to purchase new auto parts for your vehicle, we strongly suggest you consider the genuine Lexus RX350 Intake Manifold available on LexusPartsNow.com. Our OEM Lexus RX350 Intake Manifold come with the reassurance of the manufacturer's warranty, a hassle-free return policy, and speedy delivery service, all at affordable prices online. Feel free to shop with confidence!

Lexus RX350 Intake Manifold Parts Questions & Experts Answers

Manifold, Intake
17111-0P030
Q: How to remove and install Intake Manifold in Four cylinder engine on Lexus RX350?
A: To remove the intake manifold, first relieve the fuel system pressure and disconnect the cable from the negative battery terminal. Next, remove the air intake duct and resonator, followed by the cowl cover assembly. Then, take out the fuel rail and injectors as an assembly. For models from 1999 to 2007, remove the throttle linkage and throttle body from the intake manifold, label and detach the PCV and vacuum hoses connected to the intake manifold, and securely support the vehicle on jackstands. If working on a 4WD model, loosen the right side driveaxle/hub nut and the right front wheel lug nuts before raising the vehicle. Drain the transfer case lubricant, remove the right side driveaxle, and separate the transfer case mount from the transfer case, removing the transfer case mounting brace. For all models, work below the vehicle to remove the manifold lower mounting bolts, then from above, remove the intake manifold upper mounting nuts and bolts, and take out the manifold, gasket, and manifold insulator from the engine. For models from 2008 and later, remove the engine cover, disconnect the vacuum hoses and ventilation tubes from the intake manifold, and remove the throttle body with the electronic throttle actuator. Additionally, remove the windshield wiper motor, brake booster vacuum bracket, and outer cowl top assembly, then disconnect and remove the main harness connector to the intake manifold and tumble control valves. Apply battery voltage to the tumble control valve electrical connector to close the valve, preventing damage during removal. Remove the intake manifold support bracket and disconnect the vacuum switching valve assembly electrical connector, then unscrew the intake manifold mounting fasteners and remove the manifold. For installation, clean the mating surfaces of the intake manifold and cylinder head mounting surface, checking the gasket for leaks and the manifold for warpage. Press a new gasket into the grooves on the intake manifold, install the manifold and gasket over the studs on the cylinder head, and tighten the manifold-to-cylinder head nuts/bolts in three or four equal steps from the center outwards. Reinstall the remaining parts in reverse order, check the coolant level, refill the transfer case for 4WD models, and ensure the throttle linkage operates smoothly before starting the engine to check for coolant and vacuum leaks.